HP 445946-001 User Manual Page 165
- Page / 198
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Remote monitoring
165
3. Apply, verify, and save the configuration.
RMON group 9—events
The RMON Event group allows you to define events that are triggered by alarms. An event can be a log
message, an SNMP trap message, or both.
When an alarm is generated, it triggers a corresponding event notification. Use the /cfg/rmon/alarm
x/revtidx and /fevtidx commands to correlate an event index to an alarm.
RMON events use SNMP and syslogs to send notifications. Therefore, an SNMP trap host must be
configured for trap event notification to work properly.
RMON uses a SYSLOG host to send syslog messages. Therefore, an existing SYSLOG host
(/cfg/sys/syslog) must be configured for event log notification to work properly. Each log event
generates a SYSLOG of type RMON that corresponds to the event.
Configuring RMON Events (CLI example)
1. Configure the RMON Event parameters.
>> /cfg/rmon/event 5 (Select RMON Event 5)
>> RMON Event 5# descn "SYSLOG_generation_event"
>> RMON Event 5# type log
>> RMON Event 5# owner “Owner_event_5”
2. Apply and save the configuration.
>> RMON Alarm 5# apply (Make your changes active)
>> RMON Alarm 5# save (Save for restore after reboot)
This configuration creates an RMON event that sends a SYSLOG message each time it is triggered by an
alarm.
- HP 10Gb Ethernet BL-c Switch 1
- Contents 3
- Accessing the switch 9
- Additional references 10
- Typographical conventions 10
- Management Network 10
- Connecting through Telnet 11
- Configuring an IP interface 12
- SNMP v1.0 14
- SNMP v3.0 14
- Default configuration 14
- User configuration 15
- View based configurations 16
- Configuring SNMP trap hosts 17
- Secure access to the switch 20
- ○ Retries = 1-3 24
- TACACS+ authentication 25
- Authorization 26
- Accounting 27
- (CLI example) 28
- (BBI example) 29
- Secure Shell and Secure Copy 30
- Logging in to the switch 32
- • Key Exchange—RSA 33
- User access control 34
- Setting up user IDs 35
- Ports and trunking 36
- Port trunk groups 37
- Before you configure trunks 37
- Port trunking example 39
- Configuring LACP 46
- EAPoL Message Exchange 48
- 802.1x port states 49
- Supported RADIUS attributes 50
- Port-based traffic control 51
- Introduction 53
- Overview 53
- PVID numbers 54
- VLAN tagging 55
- VLANs and IP interfaces 58
- VLAN configuration rules 59
- Multiple VLANS with tagging 60
- FDB static entries 66
- Spanning Tree Protocol 68
- Bridge priority 69
- Port priority 69
- Port path cost 69
- Creating a VLAN 70
- Rules for VLAN tagged ports 70
- Multiple Spanning Trees 71
- Port Fast Forwarding 76
- Fast Uplink Convergence 76
- RSTP and MSTP 77
- Port type and link type 78
- RSTP configuration example 78
- MSTP region 80
- MSTP configuration example 81
- Quality of Service 86
- Using ACL filters 87
- • TCP/UDP 88
- Summary of ACL actions 89
- Understanding ACL precedence 89
- Using ACL Groups 90
- ACL Metering and Re-marking 91
- Viewing ACL statistics 91
- ACL configuration examples 92
- Per Hop Behavior 97
- QoS levels 98
- Queuing and scheduling 105
- Basic IP routing 106
- Example of subnet routing 109
- DHCP relay agent 112
- Routing Information Protocol 114
- RIP Features 115
- Multicast 116
- Default 116
- Authentication 116
- RIP configuration example 117
- IGMP Snooping 118
- FastLeave 119
- IGMP Filtering 120
- Static multicast router 121
- OSPF overview 131
- Neighbors and adjacencies 133
- Link-State Database 133
- Shortest Path First Tree 133
- Configurable parameters 134
- Defining areas 135
- Interface cost 136
- Default routes 137
- Virtual links 138
- Router ID 138
- • ABR Load Sharing 140
- • ABR Failover 140
- OSPF configuration examples 141
- − IF 1 142
- − IF 2 142
- Example 2: Virtual links 150
- Other Virtual Link Options 152
- Verifying OSPF configuration 154
- Remote monitoring 155
- RMON group 2—history 158
- History MIB objects 159
- RMON group 3—alarms 161
- RMON group 9—events 165
- High availability 167
- Failure Detection Pair 168
- Configuration guidelines 169
- VRRP overview 173
- VRRP operation 174
- Failover methods 175
- Active-Active configuration 178
- Task 2: Configure Switch B 180
- − IF 3 182
- − IF 4 182
- Troubleshooting tools 191
- Console and Syslog messages 195
- Trace route 195
- Customer support tools 195
Related products and manuals for Network switches HP 445946-001
Network switches HP 1410-24G User Manual
(33 pages)
(33 pages)
Network switches HP MSR2000 User's Guide
(9 pages)
(9 pages)
Network switches HP 2600-PWR User Manual
(306 pages)
(306 pages)
Network switches HP 2000fc User Manual
(26 pages)
(26 pages)
Network switches HP 4/32B SAN User Manual
(12 pages)
(12 pages)
(7 pages)
Network switches HP 5120 EI User Manual
(92 pages)
(92 pages)
Network switches HP SAN Switch User Manual
(104 pages)
(104 pages)
Network switches HP 100VG User's Guide
(26 pages)
(26 pages)
Network switches HP AA-RW20A-TE User Manual
(226 pages)
(226 pages)
Network switches HP AWSXCIG-1A User Manual
(60 pages)
(60 pages)
Network switches HP PROCURVE 3500 User Manual
(120 pages)
(120 pages)
Network switches HP 10BASE-T User's Guide
(70 pages)
(70 pages)
Network switches HP ProCurve Series User Manual
(110 pages)
(110 pages)
© 2020, manymanuals.com. All rights reserved. | 3.557 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals