HP D3600 Enclosure User Manual Page 35
- Page / 69
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Connecting power cords
When connecting power cords, use the cords shipped with the disk enclosure.
The power cord should be approved for use in your country. The power cord must be rated for the
product and for the voltage and current marked on the electrical ratings label of the product. The
voltage and current rating for the cord should be greater than the voltage and current rating marked
on the product. In addition, the diameter of the wire must be a minimum of 1.00 mm
2
or 18 AWG,
your maximum length may be up to 3.66 m (12 ft).
After power is supplied to the disk enclosure, the power supply automatically senses the input
voltage and the power supply LED illuminates as solid green.
To protect the system from power-failure-related downtime, each disk enclosure ships standard with
a redundant power supply. Depending how you connect the power supplies to the power source,
you can eliminate downtime caused by power-related failures.
Level of ProtectionConnection Method
Protects you from downtime when one of the disk enclosure power supplies fails.Connected to:
• One power source
The remaining power supply/fan module can operate the disk enclosure until you install
a replacement module.
Protects you from downtime when one of the disk enclosure power supplies fails.Connected to:
• Two separate power
sources
Protects you from data loss when one of your power sources fails, due to a pulled cable
or tripped breaker.
The remaining power source can power the disk enclosure until the failed power source
is restored or relocated. Depending on the cause and duration of the power outage, you
can use this time to properly shut down your storage subsystem.
Protects you from downtime when one of the disk enclosure power supplies fails.Connected to:
Protects you from data loss when one or both of your power sources fails, due to a pulled
cable, tripped breaker, or local power outage.
• Two UPS
• Two separate power
sources
The remaining power source or the UPS will power the disk enclosure until power is
restored to the source. Depending on the cause and duration of the power outage, you
can use this time to properly shut down your storage subsystem.
WARNING! To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Route the power cord so that it is not likely to be walked on or pinched by items placed against
it. Pay particular attention to the plug, electrical outlet, and the point where the cord is attached
to the disk enclosure.
Connecting SAS cables and power cords 35
- Abstract 1
- DescriptionDateEdition 2
- Contents 3
- 4 Contents 4
- Contents 5 5
- 6 Contents 6
- 1 Hardware 7
- LFF Front view 8
- SFF Front view 9
- Rear view 10
- Disk drives 11
- Front status and UID module 12
- Power supply module 13
- Fan module 14
- I/O module 15
- Rear power and UID module 16
- 2 Technical specifications 17
- 3 Deployment types 18
- 4 Installation 19
- Preliminary tasks 20
- Preliminary tasks 21 21
- Striping methods 22
- RAID levels 22
- Disk drive sizes and types 23
- Spare disks 23
- Array sizing 24
- Preparing the site 25
- Racking the disk enclosure 26
- Racking the disk enclosure 27 27
- 28 Installation 28
- Disk drive options 29
- Disk drive guidelines 29
- Installing a disk drive 29
- 30 Installation 30
- Preparing the server 31
- Overview 32
- Cabling best practices 32
- 34 Installation 34
- Connecting power cords 35
- Power on best practices 36
- Power on procedures 36
- 5 Configuration 38
- 6 Operation and management 39
- 40 Operation and management 40
- 7 Cabling examples 41
- Single-domain example 42
- Dual domain example 43
- 8 Troubleshooting 44
- Is the fan LED amber? 46
- Compromised fault tolerance 47
- Time required for a rebuild 48
- Handling disk drive failures 49
- 9 Replacement procedures 50
- Replacement instructions 51
- Hardware components 52
- Contacting HP 54
- Related information 55
- Customer self repair 55
- Rack stability 56
- FCC rating label 57
- Modifications 57
- Battery replacement notices 58
- Regulatory notices 60
- Japanese notices 61
- Korean notices 61
- Taiwanese notices 61
- Recycling notices 62
- Estonian notice 63
- Finnish notice 63
- French notice 63
- German notice 63
- Greek notice 63
- Hungarian notice 64
- Italian notice 64
- Latvian notice 64
- Lithuanian notice 64
- Polish notice 64
- Portuguese notice 65
- Romanian notice 65
- Slovak notice 65
- Spanish notice 65
- Swedish notice 65
- Turkish notice 66
- 68 Index 68
Related products and manuals for Disk arrays HP D3600 Enclosure
Disk arrays HP AutoRAID 12H User Manual
(20 pages)
(20 pages)
Disk arrays HP AJ758A Datasheet
(48 pages)
(48 pages)
Disk arrays HP AX670A Datasheet
(19 pages)
(19 pages)
© 2020, manymanuals.com. All rights reserved. | 0.553 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals