MPEGscope Startup Guide
1Introduction• For More Information 1-3• How To Contact Us 1-4
1-2IntroductionWelcome to MPEGscope, your new digital video test solution from Hewlett-Packard. Combining real–time functionality with offline analysi
1-3IntroductionFor More InformationFor More InformationIf you are using MPEGscope for the first time or performing a new task, MPEGscope’s online help
IntroductionHow To Contact Us1-4How To Contact UsIf you need technical support, contact the support center in your region.Location Telephone EmailNort
2Getting Started• Starting an MPEGscope Test Session 2-2• Connecting to Interfaces 2-4• Connecting an External Clock Source 2-11• Connecting an Extern
2-2Getting StartedStarting an MPEGscope Test SessionThis section leads you quickly through the necessary steps to begin testing with MPEGscope. You ca
2-3Getting StartedStarting an MPEGscope Test SessionCAUTION If you experience a problem during setup, refer to “Troubleshooting”, page 2–13, for instr
Getting StartedConnecting to Interfaces2-4Connecting to InterfacesMPEGscope comes equipped with a DVB-SPI (Synchronous Parallel Interface) on the main
2-5Getting StartedConnecting to Interfaces.CAUTION: Electrostatic Discharge (ESD)All connectors on MPEGscope and the IEEE 1394 interface are susceptib
The information contained in this document is subject to change without notice.HEWLETT-PACKARD MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS MATER
Getting StartedConnecting to Interfaces2-6To Connect to the DVB-SPI InterfaceThe DVB-SPI (Synchronous Parallel Interface) includes two adapter cables
2-7Getting StartedConnecting to InterfacesTo Connect to the ASI and Serial ECL (DHEI) InterfaceThe ASI (Asynchronous Serial Interface) and Serial ECL
Getting StartedConnecting to Interfaces2-8DHEI Interface1Connect the single DB–25 male connector on one end of the DHEI cable to the MPEGscope DHEI po
2-9Getting StartedConnecting to InterfacesTo Connect to the SMPTE 310M InterfaceThe SMPTE 310M interface is a serial-to-parallel converter for the DVB
Getting StartedConnecting to Interfaces2-10To Connect to the ARIB InterfaceThe ARIB (Association of Radio Industries and Businesses) interface is an 8
2-11Getting StartedConnecting an External Clock SourceConnecting an External Clock SourceYou can use an external clock to synchronize the MPEGscope tr
Connecting an External Trigger CableYou can use a trigger cable with a 25-pin D-type male connector to connect your external equipment to MPEGscope’s
2-13Getting StartedTroubleshootingTroubleshootingThis section lists some problems that may occur during initial MPEGscope setup.Symptom Suggested Acti
Getting StartedTroubleshooting2-14CAUTION Do not remove the cover or handle any MPEGscope hardware unless advised to do so by your HP customer support
ASpecifications• Technical A-2• General A-5• Line Interface A-6
iiiCertificationAgilent Technologies certifies that this product met its published specifications at the time of shipment from the factory. Agilent Te
A-2SpecificationsTechnicalPortions of the following standards are relevant to MPEGscope. You should be familiar with these standards before using this
A-3SpecificationsTechnical• ETR 211:1997 Digital Video Broadcasting (DVB); Guidelines on implementation and usage of DVB service information• ETR 290:
SpecificationsTechnicalA-4• ARIB STD-B10, Version 1.2• ARIB STD-B15, Version 1.0• ARIB STD-B20, Version 1.1• ARIB STD-B24, Version 1.0Interface standa
A-5SpecificationsGeneralGeneralPerformance • Transmitting from disk: • Minimum: 250 Kb/s• Maximum: 85 Mb/s for E6277B, E6277C, E6300A, E6301A,E6302A60
SpecificationsLine InterfaceA-6Line InterfacePort ConfigurationsWARNING To ensure the Electromagnetic Compatibility (EMC) of MPEGscope, use shielded c
A-7SpecificationsLine InterfaceWARNING To ensure the Electromagnetic Compatibility (EMC) of MPEGscope, use shielded cables on all interfaces. SMPTE 31
SpecificationsLine InterfaceA-8PinoutsPin SPI 26(a)a. AMPLIMITE™26-pin connectorSPI 25(b)b. DB-25 connectorM2S(c)c. SMA/SMB connectorDHEI(d)d. DB-25 c
A-9SpecificationsLine InterfacePinoutsPin ARIB(a)a. ARIB IN connector1 Data TPD7 (MSB)2 Data TPD63 Data TPD5 4 Data TPD45 Data TPD36 Data TPD27 Data T
BReinstalling Software• Reinstalling Software B-2• Performing a System Backup B-3• Performing a System Restore B-4
ivDieses Zeichen steht für ein Produkt der Gruppe 1, Klasse A, für den Einsatz im industriuellen, wissenschaftlichen und medizinischen Bereich.This pr
B-2Reinstalling SoftwareMPEGscope comes with all the software pre–installed. However, an installation disk is included in case you need to reinstall t
B-3Reinstalling SoftwarePerforming a System BackupPerforming a System BackupIf you have purchased the optional 12/24 GB DAT drive, you can perform a s
Reinstalling SoftwarePerforming a System RestoreB-4Performing a System RestoreAfter backing up the system drive to the optional 12/24 GB DAT drive, yo
Contents, Figures, TablesIndex–1Indexinner margin for textbody text bottom marginfooter rulling linefooter text baseouter margin for textRightAARIB li
Indexbody text bottom marginfooter rulling linef text base lineinner margin for textinner margin for textLefttop margin for textIndex–2setting up, 2-2
v Borne de mise à la terre de cadre ou de châssis. Connectée en principe au cadre métallique de l’équipement. Courant alternatif (ca).Courant continu
page inner marginhanging column right marginbody text left marginbody text bottom marginfooter rulling linefooter text base lineouter margin for text
Comments to this Manuals