HP 1U User Manual

Browse online or download User Manual for Electrical enclosures HP 1U. HP 1U User's Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 25
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
HP StoreEver
1U Rack-mount Enclosure User Guide
This document provides installation instructions and specifications for the HP StoreEver 1U rack-mount enclosures. It is intended
for system administrators and technicians experienced with installing tape drives and other hardware into a rack.
*606410-007*
HP Part Number: 606410-007
Published: September 2013
Edition: Fourth
Page view 0
1 2 3 4 5 6 ... 24 25

Summary of Contents

Page 1 - HP StoreEver

HP StoreEver1U Rack-mount Enclosure User GuideThis document provides installation instructions and specifications for the HP StoreEver 1U rack-mount e

Page 2

Figure 12 Attaching the cables1. Power2. Data3. SCSI ID selector switch (SCSI drives only)NOTE: Fold excess cable length and secure with the clips pro

Page 3 - Contents

NOTE: One device per SCSI bus is the recommended configuration for LTO–3 and LTO–4 drives.Figure 14 Single-device SCSI configuration2. Device 21. Devi

Page 4 - 1 Introduction

NOTE: Each SCSI device on the same SCSI bus must have a unique SCSI ID. Be sure that theSCSI ID is different for each device and that neither is set t

Page 5 - Hardware Options

3 1U Rack InstallationRail Mounting KitThe rack rails supplied with the 1U rack-mount enclosure can be used to install the unit in racksthat have roun

Page 6 - Rear Panel Components

When installing the enclosure in a rack:• Start at the bottom of the rack, or at the top of a previously mounted component, and workupward• HP recomme

Page 7 - 2. Drive blank1. Drive

1. Insert the pins in front mounting plate of the outer rack rails into the previously marked holesin the front vertical mounting columns of the rack.

Page 8 - 2 Drive Installation

1. Remove the pins and threaded plates from both ends of each outer rack rail. These pieceswill not be used.Figure 20 Removing the pins and threaded p

Page 9

3. Extend the rack rails past the rear vertical mounting columns and attach the back mountingplate of each outer rail to the rack using four 10-32 scr

Page 10 - Cabling with Two Devices

Figure 24 Connecting the power cord (USB drive installed)8. Install the cable support clips at the back of the rack rails on one or both sides of the

Page 11 - Two Devices on One SCSI Bus

4 Support and Other ResourcesContacting HPFor worldwide technical support information, see the HP support website:http://www.hp.com/supportBefore cont

Page 12 - 12 Drive Installation

© Copyright 2005, 2013 Hewlett-Packard Development Company, L.P.The information contained herein is subject to change without notice. The only warrant

Page 13 - 3 1U Rack Installation

Table 1 Document conventions (continued)ElementConventionMonospace text• File and directory names• System output• Code• Commands, their arguments, an

Page 14 - Installing the Rack Rails

5 Documentation feedbackHP is committed to providing documentation that meets your needs. To help us improve thedocumentation, send any errors, sugges

Page 15

A SpecificationsMetricS.A.E.SpecificationDimensions:4.32 cm1.7 inHeight64.14 cm25.3 inDepth42.88 cm19.0 inWidth9.07 kg20 lbWeight (1 drive installed)I

Page 16 - 16 1U Rack Installation

B Electrostatic DischargePreventing Electrostatic DischargeTo prevent damaging the system, be aware of the precautions you need to follow when setting

Page 17 - Completing the Installation

C Regulatory InformationFor important safety, environmental, and regulatory information, see Safety and ComplianceInformation for Server, Storage, Pow

Page 18 - 18 1U Rack Installation

HP Enterprise Servershttp://www.hp.com/support/EnterpriseServers-WarrantiesHP Storage Productshttp://www.hp.com/support/Storage-WarrantiesHP Networkin

Page 19 - 4 Support and Other Resources

Contents1 Introduction...4Standard Features...

Page 20 - Customer self repair

1 IntroductionThe HP StoreEver 1U Rack-mount Enclosure is a rack-mountable storage system capable of holdingup to two half-height 5.25 inch tape or RD

Page 21 - 5 Documentation feedback

Figure 2 External SAS ports on the 1U rack-mount enclosureWhen two SAS devices are installed, the right–most connector of the internal cable is connec

Page 22 - A Specifications

1U Rack-mount Enclosure ComponentsFront Panel ComponentsFigure 4 1U rack-mount enclosure front panel components1. Drive bay2. Expansion drive bay3. Po

Page 23 - B Electrostatic Discharge

Internal Components (SAS version shown)Figure 6 1U rack-mount enclosure internal components (SAS version)2. Drive blank1. Drive4. Fan assemblies (2)3.

Page 24 - C Regulatory Information

2 Drive InstallationTools RequiredA 3/16” (5mm) flat-blade screwdriver or T-15 Torx driver may be required to install a drive in the1U rack-mount encl

Page 25 - HP Networking Products

Figure 9 Removing the mounting brackets from the blank4. Install the mounting brackets to the sides of the drive. Always use the screws provided witht

Comments to this Manuals

No comments