Hp BL860C User Manual

Browse online or download User Manual for Computers Hp BL860C. HP BL860C User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 184
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews

Summary of Contents

Page 1 - Service Guide

HP Integrity BL860c Server Blade UserService GuideHP Part Number: AD217-9015CPublished: November 2011Edition: 11

Page 2

About This DocumentThis document provides information and instructions on servicing the HP Integrity BL860c serverblade.The document publishing date a

Page 3 - Contents

Enter menu item or [Ctrl-B] to Quit: e Log Name Entries % Full Latest Timestamped Entry-----------------------------------------

Page 4 - 4 Contents

6. To decode the blinking state of server LED, review the entire SEL and look at events with alertlevel 2 and above.For example:Log Entry 24: 14 Feb 2

Page 5 - Contents 5

Sensor: Entity Presence0x2000000009020050 FF01807115250300If you do not get the above Alert Level 7 (IPMI) event, but get another high level alert, re

Page 6 - 6 Contents

Processor Installation OrderFor a minimally loaded server blade, one IPF processor module must be installed in processor slot0. Slot 0 is the slot clo

Page 7 - Contents 7

ropes to support 4 Lower Bus Adapter (LBA) chips. Each LBA chip interfaces with the SBA in thezx1 chip, through one or multiple rope connections, as f

Page 8 - 8 Contents

Table 26 Rope-to-ACPI Paths (continued)Logical ACPI PathPhysical Rope #PCI BusAcpi(HWP0002,PNP0A03,0)/Pci(1 | 2)Acpi(HWP0002,PNP0A00,400)/Pci(1 | 0)1F

Page 9 - Contents 9

4. On the server blade you are updating, issue the fweupdate.efi command from the EFIcommand prompt by entering: fweupdate.BL860c.sxxxx.byyyy.mzzzz.e

Page 10 - About This Document

Online SupportTo contact HP Customer Support online, see the Worldwide Limited Warranty and TechnicalSupport Guide or visit us at http://www.hp.com/bi

Page 11 - Typographic Conventions

6 Removing and Replacing ComponentsThis chapter provides information on removing and replacing components in the server blade.Service Tools RequiredSe

Page 12 - Contacting HP

Figure 35 Removing a SAS Disk DriveCAUTION: Always populate hard drive bays with a SAS disk drive or a hard drive blank.Operating the server blade wit

Page 13 - Documentation Feedback

Chapter 2 General Site Preparation Guidelines Use this chapter to learn about the necessarysteps needed to properly install your server blade in a dat

Page 14 - 1 Overview

Figure 36 Removing a Disk Drive BlankReplacing a Disk Drive BlankTo replace the hard drive blank, slide the blank into the bay until it locks into pla

Page 15 - SAS Disk Drives

Removing and Replacing the Server Blade from the EnclosureThe following procedures describe how to remove and replace the server blade from the enclos

Page 16 - I/O Subsystem

1. Slide the server blade back into the enclosure until flush with the enclosure.2. Close the lever.NOTE: After you install the server blade back into

Page 17 - Memory Subsystem

1. Ensure the access panel latch is in the open position (pointing up) before replacing the accesscover.See Figure 39 (page 113).2. Place the access p

Page 18 - Add-On Memory

• TPM module• System boardNOTE: The server blade must be removed from the enclosure to access the internal components;therefore, no internal devices a

Page 19 - Controls, Ports, and LEDs

5. Slots DIMM 4A and DIMM 4B6. Slots DIMM 5A and DIMM 5BThe server blade uses a minimum of 1 GB of memory (two 512-MB DIMMs), and a maximum of96 GB of

Page 20 - Front Panel View

Figure 41 Processor Slot Locations on the System BoardRemoving a ProcessorTo remove a processor:Removing processor 0 is shown in this procedure.If you

Page 21 - SAS Disk Drive LEDs

Figure 43 ZIF Socket on the Processor8. Carefully remove the processor module by lifting it straight up from the system board.9. Place the processor m

Page 22 - Controls and Ports

Figure 45 Alignment Holes in Processor Slot 03. Slide the processor sequencer to the right and hold it to uncover the ZIF socket.4. Tighten the ZIF so

Page 23 - Rear Panel View

Figure 47 Installing a Processor in Slot 08. Connect the power cable to the power connector on the processor.9. Install the access panel.See “Replacin

Page 24 - 24 Overview

CAUTION A caution calls attention to important information that if notunderstood or followed will result in data loss, data corruption,or damage to ha

Page 25

5. Remove the SAS backplane by lifting it straight out of the server by the backplane handle.See Figure 48.Figure 48 Removing the SAS Backplane21SAS b

Page 26 - Safety Information

Figure 49 Removing the Front Display Assembly Housing Screws4. Remove the front display assembly from the front of the server blade by pulling it stra

Page 27 - Damaged Equipment Returns

Removing the Server BatteryIMPORTANT: Removing the server battery results in a permanent loss of important informationthat was stored in the server’s

Page 28

Figure 51 Server Battery Location1Server battery on thesystem board5. Dispose of the server battery by following your local requirements.Replacing the

Page 29 - Removing the Access Panel

4. Grasp the mezzanine card by the edges and lift it off of the port.NOTE: Mezzanine card 2 is installed above mezzanine card 1 on the system board. I

Page 30

Removing a Cache ModuleCAUTION: To avoid bending the controller board, only remove or replace the cache modulewhen it is installed in the server blade

Page 31

6. If only replacing the cache module, unplug the battery cable from the cache module.Figure 54 Disconnecting the BatteryReplacing the Cache ModuleCAU

Page 32 - Installing DIMMs

1. With the cache module battery connector facing the side of the server blade that memory cell1 abuts, line up the cache module's two connectors

Page 33 - Installing Mezzanine Cards

Figure 57 Attaching the Battery CableNOTE: Only use the 24 inch BBWC cable.IMPORTANT: The BBWC battery must remain connected to the cache module to pr

Page 34

e. Between the outermost mezzanine 2 post and the server blade power connector cablesFigure 58 Mezzanine Slot 1 or 2 BBWC Cable Routing5. If the contr

Page 35

• Applicable error message• Add-on boards or hardware• Third-party hardware or software• Operating system type and revision levelHP Contact Informatio

Page 36

e. Between mezzanine slots 1 and 2.Figure 59 Mezzanine Slot 3 BBWC Cable Routing6. Replace any mezzanine cards that were removed.See “Replacing a Mezz

Page 37 - Replacing the Access Panel

6. CAUTION: The BBWC battery must remain connected to the cache module to preserve thedata when removing the cache module to transfer data.If replacin

Page 38

9. If replacing the battery, invert the BBWC battery and push the battery plug out of the batteryconnector.Figure 62 Releasing the Battery Cable from

Page 39 - Server Power States

Figure 64 Connecting the Battery Cable3. Remove CPU 0.See “Removing a Processor” (page 116).4. If this is the first BBWC battery to ever have been ins

Page 40 - Powering On the Server Blade

Figure 66 Placing the Stickerc. Line up the wavy side of the second sticker with the wavy side of the first sticker and pressdown until they stick tog

Page 41

e. IMPORTANT: The battery must be positioned so it does not block access to the systembattery, does not rest on the system board, and is about 1/4 inc

Page 42

Figure 71 Placing Stickerc. Line up the sticker with the Daul Lock hook and loop sticker on the chassis wall by CPU0.Figure 72 Lining Up the Stickerd.

Page 43

6. Replace CPU 0.See “Installing a Processor” (page 117).Figure 74 CPU 0 Replaced7. Remove any mezzanine cards blocking access to the mezzanine contro

Page 44 - Configuring the iLO 2 MP

e. Between the outermost mezzanine 2 post and the server blade power connector cablesFigure 75 Mezzanine Slot 1 or 2 BBWC Cable Routing9. If the contr

Page 45 - Configuring the iLO 2 MP 45

e. Between mezzanine slots 1 and 2.Figure 76 Mezzanine Slot 3 BBWC Cable Routing10. Plug the battery cable into the cache module battery connector.NOT

Page 46

1 OverviewThe HP Integrity BL860c server blade is a dense, low-cost, c-Class enclosure based Intel ItaniumDual-Core processor server blade. The BL860c

Page 47 - Remote Access Allowed

11. Replace any mezzanine cards that were removed.See “Replacing a Mezzanine Card” (page 124).12. Install the access panel.See “Replacing the Server B

Page 48 - Remote Access Not Allowed

5. Grasp the failed TPM and pull it straight up off the system board.See Figure 78 (page 141) for the location of the TPM on the system board.Figure 7

Page 49

Removing and Replacing the System BoardThe following procedures describe how to remove and replace the system board from the serverblade. When a syste

Page 50

Figure 79 Air Baffle Locations21Processor air baffleController air baffle10. Remove the rear air baffle and the CPU power cable holder from the system

Page 51 - LAN / NIC Configuration

Figure 81 System Board13. To disengage the system board from the connector on the front display board and the keywayson the server blade chassis, use

Page 52

IMPORTANT: Make sure the front display panel connector fully seats into the system boardconnector. If the connector is not fully seated, the server bl

Page 53 - DRVCFG Utility

A Parts InformationThis appendix provides parts information for the HP Integrity BL860c server blade components(customer replaceable units [CRUs]).Ser

Page 54 - DRVCFG Utility Screens

Table 29 CRU List (continued)Exchange PartNumberReplacementPart NumberManufacturing PartNumberDescription463010–001436010–001N431644–B21Direct adapter

Page 55

B Server UpgradesThis appendix provides information for upgrading processors.Processor UpgradesThe HP Integrity BL860c server blade supports upgrades

Page 56

OpenVMSOpenVMS must be upgraded to OpenVMS V8.3-1H1 to support the processor upgrade.WindowsWindows® supports the processor upgrade.LinuxLinux support

Page 57

Figure 1 BL860c Server Blade Components6Processors1SAS backplane2DIMMs7System board8Trusted Platform module3Mezzanine card 14Mezzanine card 29Front di

Page 58

C UtilitiesThis appendix describes the utilities that are part of the server blade. These include the EFI BootManager and EFI-POSSE.NVRAM Backup Utili

Page 59

Example 1 nvrambkp -hHewlett-Packard (R) IPF Non-Volatile Configuration Back-up UtilityVersion 01.03.01 Copyright (C) Hewlett-Packard. All rights rese

Page 60 - Manage Hot Spare

Figure 83 EFI Boot SequenceThe EFI boot manager loads EFI applications (including the OS first stage loader) and EFI driversfrom an EFI-defined file s

Page 61 - CFGGEN Utility

Table 31 EFI CommandsDefinitionBCH Command Parameters (PA-RISC)BCH CommandEquivalent(PA-RISC)EFI Shell CommandThese commands are found in all other me

Page 62 - CFGGEN Utility Commands

Table 31 EFI Commands (continued)DefinitionBCH Command Parameters (PA-RISC)BCH CommandEquivalent(PA-RISC)EFI Shell CommandDisplay firmware version for

Page 63

a list of commands that appear under that BCH menu. You can then invoke help followed by bch,the menu name, and a BCH command name to display informat

Page 64

Example 2 help CommandShell> helpList of classes of commands:boot -- Booting options and disk-related commandsconfiguration -- Changing an

Page 65

Example 5 help cpuconfig CommandShell> help cpuconfigCPUCONFIG [cpu] [on|off] cpu Specifies which cpu to configure on|off Specifies to confi

Page 66

boottest off Skip all tests (for a faster boot time)boottest [test] Displays status of specific Speedy Boot bitboot

Page 67

state is entered and is different from the current state of a processor, its status changes on the nextboot. The last remaining configured processor i

Page 68

Figure 2 SAS Disk Drive SlotsFor the location of the SAS disk LEDs, see Figure 5.SAS BackplaneThe SAS disk backplane supports two small form factor (S

Page 69

Example 11 conconfig 2 primaryCommandTo change primary operating system consoleShell> conconfig 2 primaryCONSOLE CONFIGURATION Index Status Type

Page 70 - Adding the HP-UX Boot Option

Parametersmca dumps the Machine Check Abort error logcpe dumps the Corrected Platform Error logcmc dumps

Page 71 - HP-UX Standard Boot

Example 14 info all CommandShell> info allSYSTEM INFORMATIONDate/Time: Oct 31, 2003 22:03:39 (20:03:10:31:22:03:39)Manufacturer: hpProduct Name

Page 72 - fs1:, and so on

Selftest Setting --------- -------------- early_cpu Run this test late_cpu Run this test platform Run this test chipset

Page 73

Example 15 info cpu CommandShell> info cpuPROCESSOR MODULE INFORMATION # of L3 L4 Family/ CPU Logical

Page 74 - Shutting Down HP-UX

Example 18 info boot CommandShell> info bootBOOT INFORMATION Monarch CPU: Current Preferred Monarch Monarch Possible Warnings --

Page 75

Example 19 ioconfig commandShell> ioconfigDeconfigure or reconfigure IO components or settingsIOCONFIG [fast_init | wol [on | off]]fast_init Speci

Page 76 - Booting OpenVMS

Syntaxmonarch <cpu>Parameters<cpu> specifies a cpuOperationIf specified with no parameters, monarch displays the Monarch processor fo

Page 77 - Shutting Down OpenVMS

Example 22 pdt CommandShell> pdtPDT Information Last Clear time: PDT has not been cleared Number of total entries in PDT:

Page 78

Example 24 sysmode CommandShell> sysmodeSystem Mode: NORMALShell> sysmode adminYou are now in admin mode.Shell> sysmode serviceYou are now in

Page 79

To enable PCIe MPS optimization use the ioconfig mps_optimize command. See “ioconfig”(page 165).For non-PCIe systems, ioconfig and info io will not di

Page 80

1. To map the parameters for all PCI cards installed in the server, enter the info io commandat the EFI Shell prompt.A list of all the devices that ar

Page 81

Shell> devtreeDevice TreeCtrl[04] Ctrl[0A] Acpi(HWP0002,0)Ctrl[12] Usb Open Host ControllerCtrl[13] Usb Open Host ControllerCtrl[14] Acpi(HWP0002,0

Page 82

This listing shows which driver controls which device (controller). In the above example, theinterface information is shown highlighted bold. You can

Page 83 - initiate the Linux loader

PCI Device, and PCI Function to the Bus #, Dev #, and Fnc # values from theinfo io command.CAUTION: Do not change the value for any of these fields on

Page 84 - so on) that are known

Using the Boot Option Maintenance MenuThis menu enables you to select console output and input devices as well as various boot options.In all the foll

Page 85

• Removable Media Boot allows you to boot from a removable media drive (CD/DVD drive).This option does not support booting from a specific file on a s

Page 86 - 5 Troubleshooting

For example, if you normally boot using a configuration on your LAN but would like to boot froma local hard drive if the LAN is unavailable, move the

Page 87

Interrupting the timeout during the countdown stops the Boot Manager from loading any bootoptions automatically. If there is no countdown, boot option

Page 88

This option displays the console devices on your server. This normally includes a standard keyboardand mouse, and a serial port for receiving output f

Page 89

• Reset Configuration to Default lets you restore server settings to their original configuration• Help displays additional information about the avai

Page 90

Table 4 Server Blade Memory Array Capacities (continued)Single DIMM SizesMin / Max Memory Size2 GB4 GB / 24 GB4 GB8 GB / 48 GBNOTE: Installing DIMMs a

Page 91 - Troubleshooting Tools

IndexAaccess panelremoving, 29, 112replacing, 37, 112accessing iLO 2 MP, 40ACPI pathing, 104adapterpath, determining with info command, 170slot number

Page 92 - Server Health LED

replacing, 114, 115slot locations, 33, 114disabling remote access, 48disk drive backplane see SAS backplane see SASbackplanedisk drive blankremoving,

Page 93 - NIC LEDs

DIMMs, 32, 115front display assembly, 121mezzanine card, 124mezzanine cards, 33NVRAM utility, 150operating system with DVD drive, 66operating system w

Page 94 - Boot Process LEDs

slot locations, 31, 115RRB commandobtaining the enclosure name, 46rear panelports, 23, 50remote accessallowing, 47configuring, 46disabling, 47, 48secu

Page 95 - Online Diagnostics/Exercisers

connecting to server blade, 42SUV cable port, 20SUV cable port location, 22system boardremoving, 142replacing, 144system boot options, 68system config

Page 96 - Offline Support Tools List

USB Bot Mass Storage Driver: 00000020 Generic USB Mass Storage Driver: 00000020 CLPrelay App: 00000100* Indicates active system firmware image.

Page 97 - HP-UX Fault Management

© Copyright 2007, 2011 Hewlett-Packard Development Company, L.PLegal NoticesThe information contained herein is subject to change without notice.The o

Page 98 - Errors and Error Logs

Front Panel ViewThe server blade has seven server LEDs, one Power button, two Reset buttons, SAS disk drive LEDsand one front panel port that accepts

Page 99 - System Event Log Review

Figure 4 shows the front panel LEDs.Figure 4 Front Panel LEDs on the Server Blade6NIC 3 LED4NIC 1 LED1UID LED2 7Server health LED NIC 4 LED5NIC 2 LED3

Page 100 - T - Text mode

Figure 5 SAS Disk Drive LEDs21Status LEDActivity LEDControls and PortsThe following section identifies the locations and functions of the front panel

Page 101 - Supported Configurations

SUV Cable and PortsThe server blade has an SUV port used by the SUV cable. This port is located on the front of theserver blade. Figure 6 (page 22) sh

Page 102 - Troubleshooting Processors

Figure 8 BL860c Server Blade Rear Panel Ports21Power connectorGBX signal connector24 Overview

Page 103 - Troubleshooting Blade SBA

2 General Site Preparation GuidelinesThe HP Integrity BL860c server blade does not have cooling or power systems as part of the serverblade. Cooling a

Page 104 - Cooling Subsystem

3 Installing the Server Blade Into the EnclosureThis chapter covers the procedures for installing the server blade into a c-Class enclosure.Safety Inf

Page 105 - Firmware

Verify Site PreparationVerifying site preparation is an essential factor of a successful server installation, and includes thefollowing tasks:• Gather

Page 106 - Reporting Your Problems to HP

Service Tools RequiredService of this product can require the following tools:• An IPF Processor Install Tool Kit, consisting of:• Disposable ESD Kit•

Page 107 - Phone Support

2. Close the lever to lock the drive into place (2).Figure 10 Installing a Hot-Plug SAS Disk DriveInstalling Internal ComponentsUse these procedures t

Page 108 - Service Tools Required

ContentsAbout This Document...10Intended Audience...

Page 109 - Replacing a SAS Disk Drive

Figure 11 Removing the Server Blade Access PanelAfter the access panel is off, you can do the following:• Add an additional processor.See “Installing

Page 110 - Powering Off the Server Blade

Figure 12 Unlocked ZIF SocketCAUTION: Do not tighten the ZIF socket lock more than 180 degrees in either direction.This severely damages the socket an

Page 111

7. Tighten the captive screws (5 – 6) on the processor with the Torx T-15 screwdriver until snugFigure 14 Installing a Processor on the Server Blade S

Page 112

1. Locate the DIMM slots on the server blade system board.See Figure 15.NOTE: The server blade ships with at least two DIMMs installed in slots 0A and

Page 113

Figure 16 Mezzanine Port Locations on the System Board1Mezzanine port 1: PCIe x4 port2Mezzanine port 2: PCIe x8 port3Mezzanine port 3: PCIe x8 portThe

Page 114 - Removing and Replacing DIMMs

Figure 17 Mezzanine Port HeightsInstalling a Mezzanine Card in Port 1To insert a mezzanine card into the PCIe x4 port 1 on the system board:1. Line up

Page 115 - Replacing a DIMM

3. Tighten the thumbscrews on the mezzanine card until snug to secure the card to the systemboard (2).See Figure 18.Figure 18 Mezzanine Card 1 Install

Page 116 - Removing a Processor

6. Tighten the thumbscrews on the mezzanine card until snug to secure it to the system board.Figure 19 shows all three mezzanine cards installed on th

Page 117 - Installing a Processor

Figure 20 Replacing the Access Panel4. Lock the access panel cam (if necessary) by turning the cam clockwise with the Torx T–15 orflathead screwdriver

Page 118

5. Close the extraction lever (2).The server blade should come up to standby power. The server blade is at standby power ifthe server health LED is am

Page 119 - Removing the SAS Backplane

Installing a Processor...30Installing DIMMs...

Page 120 - Installing the SAS Backplane

power on to standby power when installed in a server blade enclosure. Verify the power state bylooking at the LEDs on the front panel, and using Table

Page 121

2. Use the down arrow on the front display panel to highlight Blade or Port Info.Figure 22 shows the Blade or Port Info selection highlighted on Main

Page 122 - Removing the Server Battery

Figure 24 The View Blade Info Screen6. Write down the iLO 2 MP IP address that displays on the View Blade Info screen.7. Access the iLO 2 MP through t

Page 123 - Removing a Mezzanine Card

Figure 25 Connecting the SUV Cable to the Server BladeConnecting a Terminal to the Server BladeTo establish a connection from your server to your term

Page 124 - Replacing a Mezzanine Card

4. To set the parameters, click OK.5. If running an emulator, launch it now.6. This ends the “Accessing the iLO 2 MP with No Network Connection” proce

Page 125 - Removing a Cache Module

iLO 2 MP Security RequirementsDepending on how you set up your server blade, there are security concerns regarding whetheryou allow remote access to t

Page 126 - Replacing the Cache Module

2. Enter on to set the power restore configuration to power on to full power as shown below:3. Enter y to confirm changing the power restore configura

Page 127

Remote Access AllowedNOTE: If your server blade has a DHCP server connected to the OA/iLO port on the rear of theenclosure, this procedure is not requ

Page 128

Remote Access Not AllowedIf you do not want to allow remote access to the server blade, use the following steps to disableDHCP and other remote connec

Page 129

• From the MP Main Menu, enter co to access the Console Menu.Depending on how the server blade was configured from the factory, and if the OS is insta

Page 130 - (BBWC) Battery

Exit the SAS Configuration Utility Screen...61CFGGEN Utility...

Page 131

Server Blade to Enclosure InterfaceThis section describes the interface between the server blade and the server blade enclosure. Thissections also sho

Page 132 - Replacing the BBWC Battery

Table 8 Server Blade to Enclosure Interconnect Mapping (continued)Server Blade to c-Class Enclosure MappingSlots 5 and 6Mezzanine Slot 2Slots 7 and 8M

Page 133

3. To determine the current version of the firmware:a. At the EFI Shell, enter mptutil from the directory that contains mptutil.efi.The following exam

Page 134

Common Questions About Flashing FirmwareQuestion After I update firmware on my SAS HBA, why doesn't the version string change inthe menu?Answer T

Page 135

There are general key inputs throughout the configuration utility that apply on all screens:F1 Help Context sensitive help for the cursor-resident fie

Page 136

You can view and modify the SAS controller whether it is enabled or disabled. You can use theBoot Support setting in the Adapter Properties menu to ch

Page 137

PCI Address Displays the PCI Address assigned by the system BIOS to the adapter.• Bus value range 0x00 - 0xFF, 0 - 255 decimal• Device value range 0x0

Page 138

Figure 30 Select New Array Type ScreenSelect New Array Type ScreenThe Select New Array Type screen enables you to view an existing array or create an

Page 139

in an IM. You can specify a hot spare at array creation, or aftercreation, if the array uses five disks or fewer. This field is grayed outunder the fo

Page 140 - Removing the TPM

View Array ScreenThe View Array screen enables you to view the current array configuration. To access the ViewArray screen, press Enter on the View Ex

Page 141 - Replacing the TPM

Front Panel LEDs...91Locator LED...

Page 142 - Removing the System Board

Offline Disk is offline for some other reason.Inactive Disk has been set inactive.Not Syncd Data on disk is not synchronized with the rest ofthe array

Page 143

Synchronize ArrayTo synchronize the IM array, press Enter on Synchronize Array. The screen prompts you to performthis action. Press Y for yes or N for

Page 144 - Replacing the System Board

Starting CFGGENThe cfggen utility is located on the HP IPF Offline Diagnostic and Utilities CD. To use cfggen:1. Insert the CD into the drive.2. Boot

Page 145

CREATE CommandThe CREATE command creates IM volumes on the SAS controller. Firmware and hardwarelimitations for this family of cards limit the number

Page 146 - A Parts Information

Parameters<controller #> A SAS controller number between 0 and 255.[DELETE] Specifies that the hot spare is to be deleted (omit the DELETE keywo

Page 147 - Table 29 CRU List (continued)

5. Choose the OS.6. Choose the firmware category you want to download.7. Download the firmware to a CD.Install the Latest Version of Firmware on the S

Page 148 - B Server Upgrades

4 Booting and Shutting Down the Operating SystemThis chapter covers procedures for booting and shutting down operating systems that run on theserver b

Page 149 - Processor Upgrades 149

Figure 32 Ports on the SUV Cable1Serial port2USB ports (2)3Video port3. Reset (or reconnect) the server blade, and reboot to EFI.4. Turn on the extern

Page 150 - C Utilities

5. The OS now starts loading onto the server blade. Follow the onscreen instructions to fullyinstall the OS.6. Continue with “Configuring System Boot

Page 151 - Extensible Firmware Interface

| Security Configuration | | 1 2 1.4 GHz Active | | | |

Page 152 - EFI Commands

Replacing a SAS Disk Drive...109Removing and Replacing Dis

Page 153 - Table 31 EFI Commands

Examples of autoboot commands for HP-UX:◦ Disable autoboot from the EFI Shell by issuing autoboot off◦ Enable autoboot with the default timeout value

Page 154 - EFI/POSSE Commands

1. Access the EFI Shell environment.a. Log in to iLO 2 for Integrity and enter CO to access the system console.When accessing the console, confirm tha

Page 155 - EFI/POSSE Commands 155

3. Press Enter to initiate booting using the chosen boot option.4. Exit the console and iLO 2 MP interfaces when finished using them.Press Ctrl-B to e

Page 156 - Example 3 help bch Command

All rights reservedHP-UX Boot Loader for IA64 Revision 1.723Press Any Key to interrupt Autoboot\efi\hpux\AUTO ==> boot vmunixSeconds left till aut

Page 157 - Operation

... (complete)loading symbol tableloading System Directory(boot.sys) to MFS...loading MFSFILES Directory(bootfs) to MFS...Launching /stand/vm

Page 158

2. Issue the shutdown command with the appropriate command-line options.The command-line options you specify dictate the way in which HP-UX shuts down

Page 159

• bcfg boot mv #a #b – Move the item number specified by #a to the position specifiedby #b in the boot options list.• bcfg boot add # file.efi "D

Page 160

3. At the EFI Shell environment, issue the map -Fs command to list all currently mapped bootabledevices.The bootable file systems are listed as fs0:,

Page 161

2. At the OpenVMS DCL prompt issue the @SYS$SYSTEM:SHUTDOWN command and specifythe shutdown options in response to the prompts given.NOTE: Use the com

Page 162 - Example 14 info all Command

2. Access the EFI System Partition (fsX: where X is the file system number) for the device fromwhich you want to boot Windows.For example, enter fs2:

Page 163 - EFI/POSSE Commands 163

C Utilities...150NVRAM Backup Utility...

Page 164 - Example 17 info io Command

1. From the EFI Boot Manager Menu, choose an item from the boot options list to boot Windowsusing the chosen boot option.2. Access the EFI Boot Manage

Page 165

You can use this method when using a graphical interface to the server.• Issue the shutdowncommand from the Windows command line.You can issue this co

Page 166

Booting and Shutting Down LinuxThis section covers booting and shutting down Linux on the server blade. Procedures for Red HatEnterprise Linux and SuS

Page 167 -

• bcfg boot mv #a #b – Moves the item number specified by #a to the positionspecified by #b in the boot options list.• bcfg boot add # file.efi "

Page 168

4. Allow the ELILO.EFI loader to proceed with booting the Red Hat Enterprise Linux kernel.By default, the ELILO.EFI loader boots the kernel image and

Page 169 - Specifying Parameters

Shutting Down LinuxUse the shutdown command to shut down Red Hat Enterprise Linux or SuSE Linux EnterpriseServer.The Red Hat Enterprise Linux and SuSE

Page 170 - 170 Utilities

5 TroubleshootingThis chapter provides a preferred methodology (strategies and procedures) and tools fortroubleshooting server blade error and fault c

Page 171 - Specifying Parameters 171

Should a failure occur, the front panel LEDs and the SEL helps you identify the problem or FRU:• The front panel LEDs and LAN LEDs of the server blade

Page 172 - 172 Utilities

Basic and Advanced Troubleshooting TablesUse the following troubleshooting tables to determine the symptoms or condition of a suspect serverblade. Be

Page 173 - Specifying Parameters 173

Table 13 Basic Low End Troubleshooting (continued)ActionConditionStep3. Examine the iLO 2 MP subsystem logs for events relatedto DC power rails.Preced

Page 174 - EFI Shell Paths

sysmode...168Syntax...

Page 175 - Change Boot Order

Table 13 Basic Low End Troubleshooting (continued)ActionConditionStep4. As a last resort, replace the server blade. Precedingproblem is fixed when all

Page 176 - Set Auto Boot TimeOut

Table 14 Advanced Low End Troubleshooting (continued)ActionSymptom/ConditionStepYou must hard reset the serverblade to clear the fatal conditionand bo

Page 177 - Choose:To select:

Table 15 Server Blade Front Panel LEDs (continued)StatusLED DescriptionItemOff = Not flaggedOff = Power is offServer health2Steady Green = Power is on

Page 178 - 178 Utilities

Internal Health LEDThe internal health LED indicates the internal health of the server blade. If the LED is red, the serverblade needs attention. Exam

Page 179 - Resetting Passwords

Table 20 SAS Disk Drive LEDsSAS Disk Drive StateStatus LEDActivity LEDOffline or not configuredOffOffNormal operation; no disk activityOffSolid greenN

Page 180 - 180 Index

4. PAL code configures all processors.5. System Abstraction layer (SAL) code configures all platform central electronic complex (CEC)chips, including

Page 181

Online Support Tool AvailabilityOnline diagnostics are included in the HP-UX OE media, and are installed by default.Online Support Tools ListThe follo

Page 182 - 182 Index

Table 24 Offline Support Tools List (continued)Functional AreaOffline ToolCore I/O DiagnosticCIODIAG2Card-Specific I/O Diagnostics/BISTSpecific Card I

Page 183

WBEM indication providers and EMS Hardware MonitorsHardware monitors are available to monitor the following components (these monitors are distributed

Page 184 - 184 Index

NOTE: The SEL E shows only event logs with alert level 2 or higher. The SEL defaults to alertlevel 2 on the server blade because there are some level

Comments to this Manuals

No comments