HP 11i User Manual

Browse online or download User Manual for Camera accessories HP 11i. HP 11i User's Manual

  • Download
  • Add to my manuals
  • Print

Summary of Contents

Page 1 - HP-UX 11i v2 and 11i v3

HP Fibre Channel Mass Storage AdaptersSupport Guide FibrChanl-02 (fclp) DriverHP-UX 11i v2 and 11i v3HP Part Number: J4301-90007Published: March 2008E

Page 3 - Table of Contents

1 Adapter OverviewThis manual contains information about HP Fibre Channel Mass Storage Host Bus Adapters thatuse the fclp driver. Each adapter is iden

Page 5 - List of Figures

2 Fibre Channel Adapter InstallationThis chapter contains installation prerequisites, guidelines, and procedures for each host busadapter. This chapte

Page 6

Additional HBAs may be supported; see the HP-UX Fibre Channel (fcd and fclp) Host Bus AdapterSupport Matrix at http://docs.hp.com/en/netcom.html#Fibre

Page 7 - List of Tables

NOTE: HP-UX 11i v3 does NOT support Online Deletion (OLD) with fclp.NOTE: HP-UX 11i v2 supports Online Addition (OLA) ONLY with fclp. It does NOT supp

Page 8

Attaching the Adapter to Other Fibre Channel DevicesTo attach the adapter to other Fibre Channel devices, follow these steps:1. Remove the Fibre Chann

Page 9 - List of Examples

/dev/dsk/c138t3d0 /dev/rdsk/c138t3d0NOTE: The third column represents the hardware path of the slot in

Page 10

Interpreting Hardware PathsExamples 2-1 and 2-2 illustrate the Fibre Channel hardware path format:Example 2-1 Hardware Path for a Direct Fabric Attach

Page 11 - 1 Adapter Overview

Table 2-3 Hardware Path Field Descriptions (continued)Fibre Channel Topology of HBAValueFieldPrivate LoopFabric TopologiesWith Peripheral Device Addre

Page 12

© Copyright 2008 Hewlett Packard Development Company L.PLegal NoticesThe information in this document is subject to change without notice.Hewlett-Pack

Page 14 - Installing Adapter Hardware

3 Troubleshooting and MaintenanceThis chapter describes the troubleshooting and maintenance tools available for Fibre ChannelMass Storage adapters. Th

Page 15

Device ID is = 0xfe00 PCI Sub-system Vendor ID is = 0x103c

Page 16

disk 21 0/2/0/0/0/0.108.11.0.0.1.2 sdisk CLAIMED DEVICE HP MSA VOLUMEdisk 22 0/2/0/0/0/0.108.11.0.0.1.3 sdisk CLAIMED DEVICE HP MSA VOLUMEdisk 23 0/2/

Page 17 - Verifying Connectivity

Device Type: InterfaceDevice Qualifier: Fibre-----------------------------------------------------------Severity Level: Error1Bolt Value: 88417Error

Page 18 - 0/1/2/0.8.0.255.0.1.0

Installing and Configuring Support Tools Manager and EMSSystem requirements:• HP-UX computer (servers or workstations)• HP-UX 11i v1, 11i v2, 11i v3,

Page 19

System Library (SysLib) A set of common routines for use by both the Test Controllerand the Test Modules. These routines perform I/O, stringparsing, a

Page 20

Flowchart 1: Configuration Test ProceduresThe sections below provide additional detail on the procedures listed in Flowchart 1.A. Enter theioscan comm

Page 21 - Introduction

Fibre Channel Connections TestFigure 3-2 Flowchart 2: Fibre Channel Connections TestRun the devicediagnosticsFVerify that theFC adapter isproperly sea

Page 22

Flowchart 2 Connections Test ProceduresThe sections below provide additional detail on the procedures listed in Flowchart 2.A. Verify that the Fibre C

Page 23 - HP Support Tools Manager

Table of Contents1 Adapter Overview...11HP Fibre C

Page 24 - Event Monitoring Service

Flowchart 3: Boot Test ProceduresThe sections below provide additional detail on the procedures listed in Flowchart 3.A. Is the system bootable over t

Page 25 - Procedure

4. Information is displayed, listing all of the HBAs in the system. Your listing will varydepending upon how many HBAs are installed in the system.5.

Page 26 - Diagnostic Flowcharts

7. Select (highlight) the Configure Boot Parameters option and press Enter.8. Select (highlight) the Boot Target Scan option and press Enter.9. Select

Page 27 - Diagnostic Flowcharts 27

A Regulatory StatementsThis appendix contains the regulatory statements and declarations of conformity for the HPFibre Channel host bus adapters.Regul

Page 28 - Go to Flowchart 1

VCCI Statement (Japan)Figure A-1 Japanese VCCI StatementLaser Safety StatementsCertification and Classification InformationThis product contains a las

Page 29 - Go to Flowchart 2

Laser Safety (Finland) LASERTURVALLISUUSLASERTURVALLISUUSLUOKAN 1 LASERLAITEKLASS 1 LASER APPARATFibre Channel 1063 MBaud Optical Link -kortille on as

Page 31 - Modifying the Scanning Policy

B Technical SpecificationsThis appendix provides technical specifications for the Fibre Channel Host Bus Adapters.AD299A Technical SpecificationsTable

Page 32

AD355A Technical SpecificationsTable B-2Performance CharacteristicsCharacteristicsPCI Express x4Bus Interface2.5 Gb/sPCI Express Lane SpeedDual port F

Page 33 - A Regulatory Statements

IndexCcable products, 16cabling requirements, 13customer replaceable units (CRUs), 13Ddiagnose tool, 24diagnostic flowchartsflowchart 1, configuration

Page 34 - Laser Safety Statements

Certification and Classification Information...34Product Information..

Page 35 - Laser Safety Statements 35

List of Figures3-1 Flowchart 1: Configuration Test...

Page 37 - B Technical Specifications

List of Tables2-1 Fibre Channel Adapter Bundle and Product Names...132-2 Cable Produc

Page 39

List of Examples2-1 Hardware Path for a Direct Fabric Attach Device..................182-2 Hard

Comments to this Manuals

No comments