HP Retail Integrated Barcode ScannerUser Guide
Figure 1-16 Exit Global Suffix ModeFigure 1-17 Exit Programming ModeVolumeScan the following bar code to set the scanner back to the factory default
Figure 1-22 MediumFigure 1-23 HighScan the following barcode to exit the programming mode.Figure 1-24 Exit Programming ModeVolume 5
2 Product FeaturesHP Retail Integrated Barcode ScannerWith rich feature sets, the HP Retail Integrated Barcode Scanner represents the premium level of
3 Safety and MaintenanceErgonomic RecommendationsWARNING! In order to avoid or minimize the potential risk of ergonomic injury follow therecommendatio
4 Setting Up and Using the ScannerFollow the steps below to connect and get the scanner up and communicating with its host.1. Attach the HP Retail Int
Configuring the InterfaceThe scanner supports USB as the host interface. Upon completing the physical connection betweenthe scanner and its host, sele
Country ModeThis feature specifies the country/language supported by the keyboard. The following languages aresupported:U.S. English Norwegian KoreanU
5 Programming the ScannerThe scanner is factory-configured with a set of standard default features. After scanning the interfacebar code from the Inte
Reading ParametersThe scanner default is Automatic Object Sense Reading mode. Simply present the bar code label infront of the scanner and center the
Operating ModesThe reader can operate in two scanning (read) modes, plus the illumination can be programmed forseveral different operations states (of
© 2013 Hewlett-Packard DevelopmentCompany, L.P.Microsoft and Windows are eithertrademarks or registered trademarks ofMicrosoft Corporation in the Unit
A TroubleshootingSolving Common ProblemsThe following table lists possible problems and recommended solutions.Problem SolutionScanner does not power u
●The spares part number located on the product● Condition under which the problem occurred●Error messages received●Hardware configuration● Hardware an
B Technical SpecificationsThe following table contains physical and performance characteristics, user environment andregulatory information.Item Descr
Depth of Field (Typical)1 Symbology SR: (typical)Code 39 5mil: 1.8" - 7.0" (4.7 - 17.7cm)10mil: 0.7" - 13.1" (1.7 - 33.2cm)20mil:
2D / Stacked Codes The scanner is capable of decoding the following symbologies using multiple frames (i.e. Multi-Frame Decoding):● Aztec●QR Code●D
LED and Beeper IndicationsThe scanner’s beeper sounds and its LED illuminates to indicate various functions or errors on thescanner. An optional “Gree
INDICATION DESCRIPTION LED BEEPERLabel Programming ModeAcceptance of Partial LabelIn cases where multiplelabels must be scanned toprogram one feature,
C Product LabelingThe sample label shown is for illustrative purposes only. Please view the label on your product foractual details, as they may vary.
D Agency Regulatory NoticesFederal Communications Commission NoticeThis equipment has been tested and found to comply with the limits for a Class B di
For questions regarding this FCC declaration, contact:Hewlett Packard CompanyP. O. Box 692000, Mail Stop 510101Houston, Texas 77269-2000Or, call (281)
About This GuideThis guide provides information on setting up and using the HP Retail Integrated Barcode Scanner.WARNING! Text set off in this manner
Korean NoticeLaser ComplianceThis device is classified as a Class 2 Laser Product in accordance with US FDA regulations and theIEC 60825-1.Each laser
Product Environmental NoticesMaterials DisposalSome HP LCD monitors contain mercury in the fluorescent lamps that might require special handlingat end
ᴹ∂ᴹᇣ⢙䍘઼ݳ㍐৺ަਜ਼䟿㺘ṩᦞѝഭⲴlj⭥ᆀؑӗ૱⊑ḃ᧗ࡦ㇑⨶࣎⌅NJᆎᶗI/O PCAsཌ䜞䇴༽⭫㔼⭫Ⓠ䭤ⴎ啖ḽᵰެԌ伄䜞ཌ䜞։䰻䈱䇴༽ѱᶵ༺⨼ಞૂᮙ✣ಞ⺢ⴎ傧ࣞಞᱴ⽰ኅO: 㺞⽰䈛ᴿ∈ᴿᇩ⢟䍞൞䈛䜞Ԭᡶᴿൽ䍞ᶆᯏѣⲺ䠅ൽ൞SJ/T11363-2006ḽ㿺ᇐⲺ䲆䠅㾷≸ԛс
iv About This Guide
Table of contents1 Quick Setup ...
Appendix B Technical Specifications ... 16LE
1Quick SetupUse the bar codes in this chapter to perform quick setup procedures for common tasks. Scan thefollowing bar code to set the scanner back t
Carriage ReturnScan the following bar code to set the scanner back to the factory defaults.Figure 1-4 Set All DefaultsNOTE: Scanning the “Set All Def
Figure 1-10 Exit Programming ModeTabScan the following bar code to set the scanner back to the factory defaults.Figure 1-11 Set All DefaultsNOTE: Sc
Comments to this Manuals